Product Catalogue for Standard Fasteners
Fastener, Bolt and Nut Supplier In Malaysia | Standard Bolts Standard Bolts & Nuts Sdn Bhd - We are the leading fastener, bolt and nut supplier in Malaysia, specializing in screw, bolts, nuts, construction fasteners, etc. IS 1364-3 (2002): Hexagon Head Bolts, Screws and Nuts of ... The Committee also decided to publish Indian Standard on ‘Hexagon nuts, Style 2 — Product grades A and B’ as Part 6 of IS 1364. The Part 6 will supersede 1S/1S0 4033:1979 on its publication. In 1967 version of this standard, the widths across flat dimensions for Ml O and Ml 2 size fasteners were specified as 17 mm and 19 mm respectively. IS 1364-1: Hexagon Head Bolts, Screws and Nuts of Product ...
Click here to download a printable PDF chart of this bolt head size chart. Have a question about bolt diameters and head sizes? Contact us for the answers you Jun 10, 2017 - Some basic but useful bolt information: Basic Dimensions A more comprehensive view: Which is also available as a PDF or SVG document. Metric Nut Sizes Chart Bolt And Nut Size Nut Sizes For Bolts Chart Standard Nut And Internal threads refer to those on nuts and tapped holes, while external threads Tolerances are specified amounts by which dimensions are permitted to vary Ref: DIN 933 - 1987. This standard contains specifications for fully threaded hexagon head screws with coarse metric thread for diameters M 1.6 to M 52. Common fasteners include screws, bolts, nuts and rivets. The terms Figure 4 illustrates the different parts of a standard threaded fastener. fastener size off the tap chart and prove this statement; when performing the analysis, assume Diameter. Fillet. Shank Length. Also called Major diameter. The diameter of a bolt is the Shank diameter, expressed diameter measurement can be used for fully threaded bolts. Shank Length If you print out this pdf, make sure you print it at Dec 7, 2017 MS20470. 118. Skybolt AN-MS-NAS Fastener Index Nuts, Screws, Pins. 90- 113 Length. K. Grip. Length. K thru AN81 parts of like thread and. No. .016. +. 031 MS17825 - CASTELLATED NUT, LOCKING, Regular Height.
How to calculate spanner size for a bolt pdf. Answer: 1. 1075 Standard Stud & Heavy Hex Nut Specifications Stud Threads Dia. The washer shall be big enough to spread the maximum preload on the flange or the insulation material. Size or. You can also measure from the bottom cavity of the threads from one side to the . T-Slots and T-Nuts - Metric Sizes - Engineering ToolBox Engineering ToolBox - SketchUp Extension - Online 3D modeling! Add standard and customized parametric components - like flange beams, lumbers, piping, stairs and more - to your Sketchup model with the Engineering ToolBox - SketchUp Extension - enabled for use with the amazing, fun and free SketchUp Make and SketchUp Pro .Add the Engineering ToolBox extension to your SketchUp from the … SPECIFICATION FOR STUD BOLTS AND TAP END STUDS (Revision of ANSI B1.1-1982) Standard. Size 1" and below shall have UNC threads. Size 1-1/8" and above shall have 8 threads per inch. 1.4 APPLICATION API Spec 6A, "6B" flanges, may use "R" or "RX" gaskets, "RX" gaskets producing greater standoff between flanges. Tables for "6B" flanges in this document show stud bolt and tap end stud lengths A GUIDE TO TORQUE VALUES - Norbar Torque A GUIDE TO TORQUE VALUES standard finish, uncoated and not lubricated* (b) the load will be 90% of the bolt yield strength * If lubrication has been applied to the bolt and/or the nut (other than the normal protective oil film), multiply the recommended torque by the appropriate factor shown in the table.
Fastener, Bolt and Nut Supplier In Malaysia | Standard Bolts
Mar 15, 2012 Design of bolt and nut assemblies. Annex B (informative) Thread dimensions for the test mandrel..19. wreNch SIze. M10 x 1.50 cAp Screw DIAMeter AND NutS. 934. Hex nuts ( specify pitch and class). 985. Nylon insert locknuts (specify pitch and class). 980V . PLEASE NOTE: All referenced dimensions are in inches. The below listed assortments of screws, bolts, nuts, washers, studs and threaded rods are. What it means: They want a 10mm diameter hex head cap screw with a coarse thread (must be assembled with a nut) (can be assembled by head or with a nut) Screw Sizes Coarse and Fine Threads. Inch Size. Coarse (UNC). Fine ( UNF). Jun 30, 2004 diameter high-strength bolts. When the thickness of the ply closest to the nut is less than the 3/8 in. or 1/2 in. dimensions given above The nut is an important part of the bolt assembly. Nut dimensions and strengths are specified so that the strength of the bolt is developed.1.5. Bolts are generally nut or directly to a threaded hole in one of the components. The advantages of Furthermore, in most cases the dimensions of the screw are not critical for the
- 165
- 844
- 1396
- 1319
- 876
- 389
- 968
- 1889
- 213
- 216
- 733
- 1408
- 1512
- 269
- 270
- 1963
- 1003
- 138
- 1348
- 641
- 862
- 1031
- 1919
- 1472
- 617
- 573
- 960
- 532
- 370
- 721
- 800
- 663
- 701
- 1998
- 990
- 528
- 1580
- 1419
- 1159
- 1896
- 1644
- 647
- 1734
- 350
- 1771
- 1009
- 693
- 1794
- 1338
- 155
- 288
- 1540
- 355
- 1655
- 388
- 1134
- 926
- 1924
- 702
- 304
- 1430
- 437
- 1520
- 1493
- 1416
- 71
- 707
- 1515
- 1280
- 1743
- 383
- 1584
- 979
- 1453
- 998
- 1298
- 1570
- 1701
- 1609
- 1880
- 1167
- 1194
- 215
- 434
- 1260
- 308
- 1046
- 1610
- 1857
- 1603
- 1657
- 717
- 856